10%银焊条上海斯米克HL301银焊条代理现货-电子快手网供应信息-电子快手网

商品详情

上海斯米克HL301银焊条10%银焊条
HL301说明：飞机牌HL301是含银10%的银基钎料，价格较低，但熔点高、漫流性差，钎焊接头塑性也较差，因此应用不广。
HL301用途：主要用于钎焊铜及铜合金、钢及硬质合金。
HL301钎料化学成分（质量分数）（%）

Ag

Cu

Zn

9.0~11.0

52.0~54.0

36.0~38.0

HL301钎料熔化温度（℃）

固相线

液相线

815

850

HL301钎料力学性能（值例供参考）

钎料强度/ MPa

母材

Rm/MPa

τm/MPa

451

纯（紫）铜

166

157

H62黄铜

313

166

碳钢

386

198

HL301直条钎料直径（长度为500）（mm）:为0.8、1.0、1.2、1.6、2.0、2.5、3.0、4.0、5.0.6.0。
HL301注意事项：
1、钎焊前必须严格清除钎焊处及钎料表面的油脂、氧化物等污物；
2、钎焊时须配银钎焊熔剂共同使用。

斯米克钎焊料分别有：（铜锌钎焊料），（铜磷银基钎焊料），（铝基钎焊料），（锡铅钎焊料），（镍基钎焊料).简介如下：

Category 类别	Trade-mark 牌号	Specification 规格	Melting Point 熔点(℃)	Chemical composition 主要成份(%)	Application 用途	Equivalent to AWS 相当AWS
Copper zinc 铜锌	L103	Wire & rod 丝	885-888	Cu54 Zn Rem.	Brazing of copper, bronze and steel, subjected to low load. 钎焊铜、青铜和钢等受力不大工件
Copper zinc 铜锌	L104	Foil 箔	890-930	Cu57 Mn2 Co2 Zn Rem.	Brazing of carbide cutting tool. 钎焊硬质合金刀具
Copper phosphorus 铜磷	L201	Cast rod, wire & rod, powder 铸条、丝、粉	710-800	P7 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-2
	L204	Cast rod, wire 铸条、丝	640-815	P5 Ag15 Cu Rem.	Brazing of copper, copper alloys, silver and molybdenum etc. 钎焊铜及铜合金、银、钼等金属。	BCuP-5
	L205	Cast rod, wire & rod, powder 铸条、丝、箔	640-800	P6 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-3
	L207	Cast rod, wire & rod 铸条、丝	640-770	P7 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-7
	L209	Cast rod, wire 铸条、丝	684-710	P7 Ag2 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金。	BCuP-6
Silver base 银基	L302	Wire & rod 丝	745-775	Ag25 Cu40 Zn Rem.	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L303	Wire & rod 丝	660-725	Ag45 Cu30 Zn余	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-5
	L303F	Flux coated rod 涂药丝	660-725	Ag45 Cu30 Zn Rem.	L303 coated with flux, the same application as L303. 外涂钎剂的L303，用途与L303相同	BAg-5
	L304	Foil 箔	690-775	Ag50 Cu34 Zn Rem.	Brazing of copper, copper alloys and steel etc. 钎焊铜及铜合金、钢等	BAg-6
	L308	Wire & rod 丝	779-780	Ag72 Cu Rem.	Brazing of copper and nickel under vacuum or reducing protective atmosphere. 铜和镍的真空或还原保护气氛钎焊	BAg-8
	L312	Wire & rod 丝	595-605	Ag40.Cu.Zn.Cd	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L313	Wire & rod 丝	625-635	Ag50.Cu.Zn.Cd	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-1a
	L321	Wire & rod 丝	615-650	Ag56.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-7
	L323	Wire & rod 丝	665-755	Ag30.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L325	Wire & rod 丝	645-685	Ag45.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-36
	L326	Wire & rod 丝	650-720	Ag38.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-34
Aluminum base 铝基	L400	Cast rod, wire & rod 铸条、丝	577-582	Si11.5 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊	BAlSi-4
Aluminum base 铝基	L401	Cast rod 铸条	525-535	Si5 Cu28 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊
Tin lead 锡铅	L600	Wire & rod 丝	183-185	Sn60 Sb≤0.8 Pb Rem.	Soldering of fusible metals and heat-treated part. 易熔金属及热处理件的钎焊	60Sn
	L601	Wire & rod 丝	183-227	Sn18 Sb2 Pb Rem.	Soldering of copper, copper alloys and galvanized iron plain sheet. 铜及铜合金、镀锌铁皮的钎焊。	18Sn
	L602	Wire & rod 丝	183-256	Sn30 Sb2 Pb Rem.	Soldering of copper, brass, copper alloys and galvanized iron plain sheet. 铜、黄铜、铁、镀锌铁皮的钎焊	30Sn
	L603	Wire & rod 丝	183-235	Sn40 Sb2 Pb Rem.	Soldering of copper, copper alloys, steel and zinc parts. 铜及铜合金、钢、锌制零件的钎焊	40Sn
	L604	Wire & rod 丝	183-222	Sn90 Sb≤0.15 Pb Rem.	Soldering of copper and steel for food and medicine field. 食品、医疗所需铜、钢等金属的钎焊	90Sn
	L605	Wire & rod 丝	232-240	Ag5 Sn95	Soldering of copper and steel for electrical and food field. 电器、食品所需铜、钢等金属的钎焊
	L608	Wire & rod 丝	295-305	Sn5.5 Ag2.5 Pb Rem.	Soldering of copper, copper alloys, steel and stainless steel. 铜及铜合金、钢及不锈钢的钎焊
Nickel base 镍基	L702	Powder 粉	970-1000	Cr7 B3 Si4 Ni Rem.	Brazing of stainless steel under vacuum or protective atmosphere. 不锈钢真空或保护气氛钎焊	BNi-2

Category 类别	Trade-mark 牌号	Product name 名称	Characteristics & application 特性和用途
Gas welding 气焊	CJ301	Copper gas welding flux 铜气焊熔剂	Melting point is about 650℃, flux for gas welding and brazing of copper and copper alloys. 熔点约650℃，铜及铜合金气焊或钎焊的助熔剂
Gas welding 气焊	CJ401	Aluminum gas welding flux 铝气焊熔剂	Melting point is about 560℃, flux for gas welding of aluminum and aluminum alloys. 熔点约560℃，铝及铝合金气焊的助熔剂
Silver brazing 银钎焊	QJ101	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃. 在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
	QJ102	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. 在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
	QJ102A	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. Non agglomeration. 在600-850℃范围钎焊铜及铜合金、钢及不锈钢。不易结块
	QJ112	Silver brazing paste flux 膏状银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. 在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
	QJ103	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃. 在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
Aluminum brazing 铝钎焊	QJ201	Aluminum brazing flux 铝钎焊熔剂	Brazing flux of aluminum and aluminum alloys within 450-620℃. 在450-620℃范围钎焊铝及铝合金的助熔剂
Aluminum brazing 铝钎焊	QJ207	Aluminum brazing flux 铝钎焊熔剂	Brazing flux of aluminum and aluminum alloys within 560-620℃. 在560-620℃范围钎焊铝及铝合金的助熔剂

Category 类别	Trade- mark 牌号	Chemical composition 化学成份(%)	Hardness 硬度	Application 用途
Oxy- Acetylene Flame spray- using 氧乙炔焰喷焊	F103	Cr10 B1.5 Si3 Ni Rem.	HRc 25	Spray-fusing of cast iron parts,,, such as die for glass, cylinder, and guide. 铸铁件的喷焊，如玻璃模具，汽缸、导轨
	F101	Cr10 B2.5 Si3 Ni Rem.	HRc 45	Spray-fusing of parts resistance to wear and corrosion, such as valve, the rotator and piston of pump. 耐磨、耐蚀件的喷焊，如阀门、泵转子、泵柱塞
	F101Fe	Cr10 B2.5 Si3 Fe10 Ni Rem.	HRc 45	Spray-fusing of corrosion-resistant parts, such as axle and stigma. 耐磨件的喷焊，如轴类、汽门
	F102	Cr16 B4 Si4 Ni Rem.	HRc 60	Spray-fusing of parts resistance to wear, corrosion and high temperature oxidation, such as die and piston. 耐磨、耐蚀、抗高温氧化工件的喷焊，如模具、柱塞
	F102Fe	Cr16 B4 Si4 Fe15 Ni Rem.	HRc 60	Spray-fusing of corrosion-resistant parts, such as axle and cold die. 耐磨件的喷焊，如轴类、冷模具
	F105	F102+50%WC	HRc 60	Spray-fusing of parts resistance to grain-wear , such as guide plate, scraper and blade of fan. 抗磨粒磨损场合的喷焊，如导板、刮板、风机叶片
	F105Fe	F102Fe+35%WC	HRc 60	Spray-fusing of parts resistance to grain-wear, such as guide plate, scraper and blade of fan. 抗磨粒磨损场合的喷焊，如导板、刮板、风机叶片
	F108	F102+80%WC	HRc 60	Spray-fusing of parts resistance to strong grain-wear and free machining, such as harrow teeth of dredger. 抗强烈磨粒磨损，无需加工场合的喷焊，如挖泥船耙齿
	F301	Cr5 B4 Si4 Ni30 Fe Rem.	HRc 45	Spray-fusing of vulnerable parts of agricultural machinery and mining machinery, such as gear and axletree. 农机,矿山机械易损件的喷焊，如齿轮，车轴
	Track iron powder 轨铁粉	Cr5 B1.5 Si3 Ni30 Fe Rem.	HRc 28	Repair spray-fusing of defects such as scratch and concavity of railroad track. 铁路钢轨擦伤、低塌等缺陷的修复喷焊
Oxy-acetylene flame spraying 氧乙炔焰喷涂	F111	Cr5 B1.5 Si3 Ni30 Fe Rem.	HB 150	Spraying of bearing and cutting parts etc. 轴承、切削件等的喷涂
	F113	Cr10 B1.5 Si3 Ni Rem.	HB 250	Spray-fusing or spraying, such as roll, piston and axle of wear and corrosion resistance. 喷涂亦可喷焊，如滚筒、柱塞、耐蚀耐磨轴等
	F313	Cr15 B1.5 Fe Rem.	HB 250	Spraying of dryer of papermaking and axle. 造纸烘缸、轴类的喷涂
	F314	Cr18 Ni9 B1.5 Fe Rem.	HB 250	Spraying of axle. 轴类喷涂
	F412	Sn10 P0.3 Cu Rem.	HB 80	Spraying of axle and bearing. 轴、轴承的喷涂
	F512	复合Al5Ni95		Backing spray of transition layer between base and working layer. 喷涂层的基体与工作层之间过渡（打底）层用喷涂
PTA hardfacing 等离子弧喷焊	F221	Cr26 W5 B0.7 Co Rem.	HRc 43	PTA hardfacing of sealing surface of high temperature and high pressure valve and the edge of hot shearing tool. 高温高压阀门密封面、热剪切刃口的等离子喷焊
	F223	Cr21 W5 B1.5 Co Rem.	HRc 40	PTA hardfacing of parts resistance to wear and corrosion at high temperature, such as valve under high temperature and high pressure, and blower. 高温下耐磨耐蚀件的喷焊，如高温高压阀门、鼓风机
	F321	Cr13 B1.5 Si1 Fe Rem.	HRc 45	PTA hardfacing of corrosion-resistant parts under mid-temperature and mid-pressure, such as stop-plate etc. 中温中压阀门的闸板及其他耐磨件的等离子喷焊
	F322	Cr23 Ni13 Si5 B1 Fe Rem.	HRc 40	PTA hardfacing of corrosion-resistant parts under mid-temperature and mid-pressure, such as valve base etc. 中温中压阀门的阀座及其他耐磨件的等离子喷焊
	F422	Sn10 P0.3 Cu Rem.	HB 80	PTA hardfacing of axle and bearing etc. 轴、轴承等离子喷焊