(2)改变转速的方法：改变皮带轮外径或改变齿轮减速器传动比，也可选用不同转速的动力机。

(3)水泵转速改变后，其流量(Q)、扬程(H)和功率(N)的变化关系如下式所示： Q1=Q*n1/n   H1=H*(n1/n)2    N1=N*(n1/n)3

 式中：Q1、H1、N．分别代表转速改变后的流量、扬程和功率。 Q、H、N分别代表规定转速下的流量、扬程和功率。

(4)水泵转速提高后，耗用功率增加，吸上真空度降低，寿命缩短。过分提高转速会发生其它事故，故应慎用。

(5)水泵转速过分降低时，泵的使用效益低，为此，应尽量避免泵在过低转速下运行。用户应按性能曲线图选择使用。

农用混流泵@新市农用混流泵@250HW-7农用混流泵当天发货

混流泵是介于离心泵和轴流泵之间的泵型需要把压水室规划成径导游叶(正导叶)加上类球形泵壳的构造型式是叶轮内安稳的相对运动的条件。为此，请求在导叶中的螺旋线有些的液体，不受任何外力的效果。

2、允许吸上真空度[Hs]与必需汽蚀余量[NPSH]r的换算关系：

 [Hs]≈10-[HPSH]c

 [NPSH]r≈[NPSH]C+0.3

 式中：[Hs]-允许吸上真空度   米

 [NPSH]C-临界汽蚀余量   米

 [NPSH]r-必需汽蚀余量   米

农用混流泵@新市农用混流泵@250HW-7农用混流泵当天发货

 *特征描述

HW 型蜗壳式混流泵是按国家标准系列而设计的高节能产品。其性能指标均达到先进水平，省材节能效果显着。延伸搜索：水环真空泵

（一）用途
HW型混流泵为卧式、单级、单吸、悬臂蜗壳式混流泵，适用于农田排灌、工业、城镇给排水及船坞、码头引水等。延伸搜索：水环真空泵
（二）特点
体积小、重量轻、流量大、效率高，汽蚀性能好，区范围宽广而平坦，结构简单，使用管理方法，维修容易。延伸搜索：水环真空泵
（三）型号说明
以250HW—8为例：
250—泵进（出）水口直径为250毫米。
8—泵总扬长为8米。

（四）水泵的传动方式
我厂生产的HW型系列混流泵均机（电）两用，其转动方式视各地区动力情况而定，订货时根据原动机的型号（功率、转速）确定水泵的传动方式，以定皮带轮的大小或联轴器的规格。延伸搜索：水环真空泵
（五）水泵转向：
从水泵进水口看叶轮为逆时针方向旋转（即箭头所示的方向旋转）。

农用混流泵@新市农用混流泵@250HW-7农用混流泵当天发货

轴承发热，轴封发热，转子窜动大，发生水击一，泵不能发动或发动负荷大要素及处理办法如下。原动机或电源不正常。处理办法：查看电源和原动机状况。泵卡住。处理办法：用手盘动联轴器查看，必要时崩溃查看，消除动静有些毛病。填料压得太紧。处理办法：放松填料。排出阀未关。处理办法：封闭排出阀，从头发动。平衡管不晓畅。处理办法：疏通平衡管。

Instructions for use (i) the HW mixed-flow pump is composed of main parts such as pump body, pump cover, impeller, pump shaft and bearing body. (Ii) The pump cover is a part of the pump connected to the inlet pipe, with a specified axial end gap between the end surface and the impeller (maintaining the specified axial clearance after eliminating the axial activity gap of the bearing). The gap is too small to produce friction, too large will lead to the pump pressure water reflux, so that the pump efficiency is reduced, through the increase or decrease adjustment paper pad to meet the required requirements of the gap. Extended search: Water ring Vacuum Pump (iii) The sealing device is composed of a filler letter, a water seal letter, a filler cover and a lead powder (or oil immersion) asbestos root. Its role is: 1, in the tea to prevent air inhalation pump, play a sealing role. 2. When pumping, prevent water from flowing out of the pump too much along the shaft. (Iv) Shaft application to protect the shaft does not make it directly friction with the filler, if long-term use found that the bushing wear too much, can change the bushing. (V) The two supports of the pump shaft are bearings in the bearing body, and the bearing has an appropriate amount of grease in its body to lubricate the bearings. (Vi) The baffle on the shaft prevents water from flowing into the bearing body along the pump, thus protecting the bearing and extending its service life.