商铺名称：东莞市霖达电子有限公司
联系人：叶江（先生）
联系手机：
固定电话：
企业邮箱：1520470554@qq.com
联系地址：东莞市石碣镇西南村明珠西路43号
邮编：523000
联系我时，请说是在电子快手网上看到的，谢谢！
1.規格型號和安規認證
MODEL NUMBER AND SAFETY CERTIFICATION
品名規格：系列號+額定電流+額定電壓+認證符號
Model Number: Part Number+Rated Current+Rated Voltage+Approvals.
例子[example]:
? ?3GFU，? ? ? ? 2A，? ? ? ? 125V/250V
1)系列號 Part Number，2)額定電流 Rated Current，3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓 ???????????????Rated Current And Voltage
????額定電流：100mA~10A ??????????????Rated Current: 100mA~10A
????額定電壓：250V AC ????????????????Rated Voltage:250V AC
1-3 標示 Marking
????保險絲上需有下列標示???????The fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓 ??Specification:Characteristic Symbol+Rated Voltage
100mA~800mA : _mA125V/250V ??1A~10A: _A125V/250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals
100mA~10A:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍 ?SCOPE
??適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構 ?OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（單位：mm）Outline Drawing and Dimensions(Unit:mm)
3-2 結構 Structure
|
編號No. |
元件Component |
材質Material |
數量Quantity |
|
1 |
熔絲?Wire |
合金? ??Alloy |
1 |
|
2 |
銅帽?Cap |
黃銅鍍鎳??Brass with mickel plated |
2 |
|
3 |
本體?Body |
玻璃管? ?GLASS Tube |
1 |
|
4 |
引線?Lead |
鍍錫銅線??Tinned Copper wire |
2 |
4.外觀及形狀；APPEARANCES AND CONFIGURATION
4-1 外觀：不應有破碎、明顯的汙斑；Appearances:There shall no fragmentation and of remarkable blotch.
4-2 形狀：帶腳的保險絲；Configuration:Axial Leaded Fuse.
5.物理特性；PHYSICAL CHARACTERISTIC
5-1 拉力測試;沿端子的軸向施加 10N 的拉力，持續 1 分鐘。
Tensile test;Keep pulling the cap of the fuse with 10N at axial
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性：
Acting Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
? ? ?50A? ? ? ? ? 250V? ? ? ? ? AC
b、Electrical characteristics
Time Lag
| Rated?current | %?of?Ampere? | Opening?Rating?Time |
| 100mA~?10A | 100% | 200% |
| 4?hours,?Minimum | 5?seconds,?Max. |
c、Temperature character
当100%的电流下温度上升不超过75℃
When 100% of rating the temperature rise doesn’t exceed 75℃.
Average?Time?Current?Curves.
7.環境特性
?ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃? 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
